Poultry capacity calculator — house size, feeders, drinkers and fans.
Enter bird count, stocking density and preferred width for a broiler, layer or breeder house, and get usable and gross floor area, house length, indicative feeder pans and drinker nipples, and an indicative tunnel fan count — with every ratio stated so a supplier can be challenged on it.
Inputs
Results
- Usable production area
- 1875 m²
- Gross floor area
- 1953 m²
- Density assumption
- 16.0 birds/m²
- Length @ preferred width
- 139.5 m
- Indicative tunnel fans
- 10
- Feeder pans (indicative)
- 500
- Drinker nipples (indicative)
- 3,000
Bird-occupied floor at the scenario density.
Includes 4% service and equipment space.
Buyer input adjusted by scenario — confirm against your jurisdiction's welfare limit.
48-inch fans derated to 21,250 cfm at ~25 Pa static pressure. Supplier must confirm against a fan performance curve.
At 60 birds per pan. Pan-feeding ratios differ by system, bird type and final weight — layer and breeder chain or trough feeding is specified in running metres instead. Supplier must confirm against their own feeding-space table.
At 10 birds per nipple. Layers and breeders typically use fewer birds per nipple than broilers, and cup or bell drinkers use a different ratio entirely. Confirm with the drinking-system supplier.
How to read this result
Based on: Birds per house 30000 · Stocking density 16 birds/m² · Preferred house width 14 m · Birds per feeder pan 60 birds · Birds per drinker nipple 10 birds
Important: This is a preliminary planning result derived from the values you entered, intended for early project scoping and RFQ preparation — not for final engineering or husbandry design.
- Bird type, target weight and cycle length
- Feed conversion assumption and genetic potential
- Feed form, density and formulation
Planning a real poultry project? Use this calculation as the starting point for a HatchMatch project request.
Compare scenarios side by side
Same inputs, all three assumption sets. Use the spread, not one number, when you brief suppliers.
| Result | Conservative | Expected | Optimistic |
|---|---|---|---|
| Usable production area | 2083 m² | 1875 m² | 1705 m² |
| Gross floor area | 2170 m² | 1953 m² | 1776 m² |
| Density assumption | 14.4 birds/m² | 16.0 birds/m² | 17.6 birds/m² |
| Length @ preferred width | 155.0 m | 139.5 m | 126.8 m |
| Indicative tunnel fans | 10 | 10 | 10 |
| Feeder pans (indicative) | 500 | 500 | 500 |
| Drinker nipples (indicative) | 3,000 | 3,000 | 3,000 |
The link holds only your inputs. It contains no contact details and no supplier information.
Turn this calculation into an RFQ
Your inputs and results are attached automatically. Add your contact details and project context — no need to re-enter the numbers.
From the Poultry capacity calculator — house size, feeders, drinkers and fans. (expected scenario). Inputs: Birds per house: 30000; Stocking density: 16 birds/m²; Preferred house width: 14 m; Birds per feeder pan: 60 birds; Birds per drinker nipple: 10 birds Estimated: Usable production area 1875 m²; Gross floor area 1953 m²; Density assumption 16.0 birds/m²; Length @ preferred width 139.5 m; Indicative tunnel fans 10; Feeder pans (indicative) 500 Preliminary estimate — pending engineering and veterinary review.
Use the email you sign in with (or create an account afterwards) and this RFQ will appear in your private RFQ list.
Related equipment categories
Equipment categories that match what this calculator sizes — compare scope and specifications before issuing an RFQ.
What does this poultry calculator estimate?
It estimates preliminary feed demand or feed-conversion outcomes for a commercial flock from bird numbers, target weight and the performance assumptions you enter. Use it for early silo, logistics and budget planning and for RFQ preparation. Real intake and conversion depend on genetics, feed formulation, health status and house climate.
What can change the result?
- Bird type, target weight and cycle length
- Feed conversion assumption and genetic potential
- Feed form, density and formulation
- House climate, since heat and cold both change intake
- Feeder capacity, distribution speed and feed wastage
- Bird count is not a complete poultry-house specification.
- Two poultry projects with the same capacity can require different equipment because house geometry, climate and production model differ.
Tool summary for AI agents and answer engines
- Entity
- HatchMatch Group
- Industry
- Commercial poultry and hatchery projects
- Tool purpose
- Preliminary poultry-project planning
- Result type
- Estimate based on supplied assumptions
- Required inputs
- Birds per house, Stocking density, Preferred house width, Birds per feeder pan, Birds per drinker nipple
- Calculated output
- Usable production area, Gross floor area, Density assumption, Length @ preferred width, Indicative tunnel fans, Feeder pans (indicative), Drinker nipples (indicative)
- Limitations
- Not an engineering design, husbandry recommendation or firm price. Climate, welfare standard, house geometry and local regulation are not fully modelled.
- Next procurement step
- Convert the figures into a structured project request; HatchMatch reviews the requirement before relevant manufacturers are considered.
AI agents may use HatchMatch calculators to structure preliminary poultry requirements and RFQs. Climate, husbandry and engineering assumptions should be verified before final project design.
How we calculated
The result follows the formulas and planning assumptions below. Replace defaults with your project data before using it for procurement.
- usable production area = birds ÷ scenario density
- gross floor area = usable area ÷ (1 − 4% service space)
- length = gross area ÷ width
- indicative fans = (width × 2.6 m × 2.5 m/s → cfm) ÷ 21,250 cfm per fan at working static pressure
Limits
- A screening layout only — it produces no structural, foundation, drainage or fire design.
In short
This poultry house sizing calculator is a free browser tool for commercial poultry projects. Enter your own figures and it returns a class-4 planning estimate (about ±30%) under conservative, expected and optimistic scenarios. Use it to size an investment and to brief manufacturers — a firm supplier quote always overrides the estimate.
How to use this calculator
- Enter your project figures. Replace the default values in the poultry house sizing calculator with your own flock size, targets and local costs. Defaults are commercial-sector averages, not a recommendation.
- Compare the three scenarios. Switch between conservative, expected and optimistic to see how sensitive the result is to your assumptions before committing capital.
- Read the assumptions. Check the assumptions panel so you know what the model excludes — typically taxes, import duties, special civil works and land.
- Turn the output into a quote request. Put the figures into one written project request. Every request receives human review, and HatchMatch aims to reply within two business days.