This guide explains what the hatchery capacity calculator computes, how each input changes the result, and how to turn the output into a comparable request for quotation. Worked examples below are produced with the same engine that powers the live tool.
Replace the default values in the hatchery capacity calculator with your own flock size, targets and local costs. Defaults are commercial-sector averages, not a recommendation.
2
Compare the three scenarios
Switch between conservative, expected and optimistic to see how sensitive the result is to your assumptions before committing capital.
3
Read the assumptions
Check the assumptions panel so you know what the model excludes — typically taxes, import duties, special civil works and land.
4
Turn the output into a quote request
Put the figures into one written project request. Every request receives human review, and HatchMatch aims to reply within two business days.
Every input explained
Default values are commercial-sector averages. Replace them with your own figures — your data always overrides the defaults.
Saleable chicks required (per week)
Day-old chicks you must deliver each week at full operation. — 100,000
Fertility (%)
Fertile eggs as a share of eggs set — driven by breeder flock age and management. — 95
Hatch of fertile (%)
90
Chick cull / grade-out (%)
2
Take-off days per week (days)
More take-off days spread the peak and shrink the chick room. — 1
Setter cabinet capacity (eggs)
Typical single-stage setters run 19,200–115,200 egg places depending on model. — 57,600
Hatcher cabinet capacity (eggs)
19,200
Chicks per box (chicks)
100
Worked examples
Three realistic cases, computed live with the calculator engine.
Baseline case
Reference values under the expected scenario — a good starting point for a first project.
Inputs
Saleable chicks required100,000 per week
Fertility95 %
Hatch of fertile90 %
Chick cull / grade-out2 %
Take-off days per week1 days
Results
Eggs to set per week119,346 eggs
Eggs to set per day (7-day)17,049 eggs
Saleable chicks per take-off day100,000 chicks
Chick boxes per take-off day1,000 boxes
Scale-up case
The same project with flock size increased 2.5×, to show how the result scales.
Inputs
Saleable chicks required250,000 per week
Fertility95 %
Hatch of fertile90 %
Chick cull / grade-out5 %
Take-off days per week1 days
Results
Eggs to set per week307,787 eggs
Eggs to set per day (7-day)43,970 eggs
Saleable chicks per take-off day250,000 chicks
Chick boxes per take-off day2,083 boxes
Conservative case
Reference values under the conservative scenario, with a safety margin on performance.
Inputs
Saleable chicks required100,000 per week
Fertility95 %
Hatch of fertile90 %
Chick cull / grade-out2 %
Take-off days per week1 days
Results
Eggs to set per week123,461 eggs
Eggs to set per day (7-day)17,637 eggs
Saleable chicks per take-off day100,000 chicks
Chick boxes per take-off day1,000 boxes
Planning assumptions
The hatchery capacity calculator uses common commercial-sector parameters; your own measured data always overrides the defaults.
The conservative scenario adds a safety margin; the optimistic scenario assumes favourable operating conditions.
Taxes, import duties, special civil works and land cost are excluded unless stated otherwise.
It is a class-4 planning estimate (roughly ±30%). Use it to compare options, size an investment and prepare a quotation request — it does not replace engineering design or a bankable feasibility study.
Yes, that is the intended use. Turn the results into a requirement list and send a single request to receive comparable offers from qualified third-party manufacturers. Any firm quote overrides the estimate.
Yes. Climate, grid voltage and stability, labour cost, import duties and logistics all move both the sizing and the cost. State the country in your request so the adjustment is priced into the offer.
Use the guide to understand the inputs and see worked examples, then run the calculator with your own figures. Both pages are free and require no registration.
Convert it into a requirement list and send one request for quotation. You receive comparable offers from qualified third-party manufacturers, and each firm quote replaces the estimate.
